/ HELP: Pre-threaded SpeedAdjust buckle
I use a BD Primrose. It's not the thread-back to secure type, it's the pull to tighten then forget (until it works loose!) type. Other manufacturers call them ziplock.
Google for pictures, you can see what type of buckle they use if you look closely
Ah, the SA is indeed different but the buckles appear similar.
Did you know you are supposed to thread the ends through the elastics keeping the buckle and webbing in a straight line ?
If you're too large ( or your harness too small depending on your viewpoint ) and don't have enough slack to do that, or don't bother they are potentially dangerous.
I didn't mean to imply they slip under load or anything like that, they don't, merely that they do occasionally need a little pull to keep them snug or at least my one does.
> I didn't mean to imply they slip under load or anything like that, they don't, merely that they do occasionally need a little pull to keep them snug or at least my one does.
Especially under the weight of a Gogarth rack!
It is like a thread back buckle, but instead of there being a single buckle, there are two pieces to the buckle and the waist strap is prethreaded through the two pieces.
You can loosen the harness by pulling the belt at an angle, and can tighten it by pulling it in line with the buckle.
Probably best to go into a shop and look at a live one if you have never seen one before.
Like someone above said, in some circumstances, they can loosen. I have one myself, and have had no problems at all with it.
Advantages are, because they are already threaded, you don't need to thread them and therefore, you can't accidentally forget to rethread them as it is already done for you. Also, no problems when they get older of trying to rethread a furry old belt!
That was my point. I was told this last week by someone very reliable who was told by a manufacturer that they can slip under load if not correctly fastened i.e. the end of the webbing that passes through the buckle must be passed through one of the elastics provided to ensure they stay in line with each other and stay locked.
A bit like the gri gri of the harness world. They are not as hands free as you may think.
I can't see how that (slipping under load because of a free tail) could happen to be honest. Ok, if the tail gets pulled way from the buckle tilting/opening it slightly while the buckle/belt is under load then yeah, I can see it could slip and an unsecured tail is more likely to get pulled away than one that's clipped/tucked away neatly. I guess that's maybe what was meant?
Anyway, all I meant to say was that I find mine do creep a bit over time even when secured properly. It's not alarming or dangerous, just something that occasionally needs a little attention. It's not a problem, I'm quite happy with it, it's comfy, fits and works fine :)
I am more than happy with my petzl one with the same style buckle as well.I know that's not what you meant and i am not trying to be alarmist or hi-jack the thread. It was just a new bit of info i picked up last week that surprised me.
It was about them being kept in line with the buckle so yes i think it's the movement away from the buckle that can be a problem. It just came up whilst discussing a client who was a bit of a squeeze in a large harness. I presumed no/not much tail was needed with this style of harness - i was wrong.
Elsewhere on the site
Make the most of this months HALF PRICE OFFER on the Five Ten Guide Tennie Mid!! Designed as a hybrid approach and... Read more
I am Matthew Phillips, I'm nearly 14 and I was born without my right arm below the elbow. I started climbing at taster... Read more
The Christmas Gift Guide at Outside.co.uk Check out our top selection of Christmas Gift Ideas for climbers,... Read more
2012 saw the release of the beautiful first volume of definitive Yorkshire Gritstone climbing, produced by the YMC with Robin... Read more
Halifax-based John Colton (see his UKC Gallery here) has an art exhibition in Courmayeur, Italy (the Italian side of Mont Blanc)... Read more